雙組份打膠機出現斷膠的解決方法
雙組份打膠機選用PLC控制，并選用多泵運動供膠，在運行全過程中不容易造成死點，混料均勻打膠平穩，并制定供膠桶出膠口在正下方，膠不容易造成殘留浪費問題，對膠的流淌性規定不高（流淌性好點的膠），如果膠太稠出膠不順暢，該機的出膠壓力可及時調節，運動頻率低磨損少。為此小編對雙組份打膠機出現斷膠的解決方法如下：
The two-component glue dispenser is controlled by PLC, and the multi pump movement is used for glue supply. It is not easy to cause dead spots during the whole operation process. The mixing is even and stable. The glue outlet of the glue supply bucket is directly below, so the glue is not easy to cause residual waste. The regulations on the fluidity of the glue are not high (glue with better fluidity). If the glue is too thick and the glue is not smooth, the glue outlet pressure of the machine can be adjusted in time, and the movement frequency is low and the wear is less. For this reason, the solution to break the two-component glue dispenser of the small knitting machine is as follows:
一、雙組份打膠機是為了增加制作效率調節是輸送帶的速度迅速，出膠量無法調節，造成時斷時續的根本原因之一。
1、 The two-component rubber beater is designed to increase the production efficiency. The adjustment is one of the fundamental reasons for the rapid speed of the conveyor belt and the inability to adjust the rubber output, causing intermittent.
二、針對膠缸和膠頭的溫度沒設置好，到時有的膠沒達到應有的溫度，造成出現鋸齒狀類的狀態。
2、 The temperature of the rubber cylinder and the rubber head is not set properly, and some rubber does not reach the proper temperature, resulting in a serrated state.
三、雙組份打膠機建議把溫度調節到合適的溫度，使丁基膠化掉，如此幾乎不容易出現以上難題。
3、 It is recommended to adjust the temperature of two-component rubber beater to a proper temperature to melt the butyl rubber, so that the above problems are hardly likely to occur.
四、如果是從雙組份打膠機一開始用到到現在一直是這種狀態膠頭出膠口有毛刺膠頭一般有二種膠口處有槽和無槽二種。
4、 If the two-component sealant dispenser has been in this state since it was first used, there are generally two types of rubber head with burr at the rubber outlet: the rubber head with groove and the rubber head without groove.
五、換膠后出現這種狀態溫度到達上限后出膠異常膠口處膠沒完全融化手動排出來一小部分膠也就是打幾個框子將壓力調大多打幾個框子將膠缸內的膠擠實。
5、 After changing the rubber, this state occurs. After the temperature reaches the upper limit, the glue at the abnormal glue outlet is not completely melted. A small amount of glue is discharged manually, that is, several frames are set to adjust the pressure, and several frames are set to squeeze the glue in the glue tank.
六、雙組份打膠機采購的丁基膠質量差，硬件配置低成本，雜質阻塞造成的。
6、 The butyl rubber purchased by two-component rubber beater is of poor quality, low hardware configuration cost, and caused by impurities blocking.
七、放膠后沒進行放氣。
7、 No air bleeding was carried out after putting glue.
雙組份打膠機出現斷膠的解決方法就從七個方面來講解了問題，當然您在使用打膠機前后要注意它的檢查與維護，才能大限度的避免問題的產生。更多相關實現就來我們網站
http://www.vrqf.com.cn咨詢了解吧！
The solution to break of two-component sealant dispenser is explained from seven aspects. Of course, you should pay attention to its inspection and maintenance before and after using the sealant dispenser to avoid problems to a large extent. More related implementations come to our website http://www.vrqf.com.cn Ask and understand!
上一篇：如果打膠機沒有自動清洗功能要如何清洗？
下一篇：自動打膠機的那些不為人知的小功能
