淺談丁基膠打膠機阻塞的原因
隨著市場競爭的日益激烈，一些廠家使用劣質丁基橡膠，其中含有很多雜質。如果長期使用，丁基膠點膠機的膠槍會被堵塞。那么我們應該怎么做?下面
濟南雙組份打膠機廠家為您解說一番。
With the increasingly fierce market competition, some manufacturers use inferior butyl rubber, which contains many impurities. If used for a long time, the glue gun of the butyl glue dispenser will be blocked. So what should we do? The following is an explanation for you from the Jinan two-component gluing machine manufacturer.
丁基膠點膠機堵塞原因:
Reasons for blocking of butyl glue dispenser:
1.打膠過程中，停止時間較長，或多次堆積，打膠結束時無法完成清洗，尤其在夏季溫度較高時。
1. During the gluing process, the center stops for a long time, or the center accumulates for many times, and the cleaning cannot be completed at the end of gluing, especially when the temperature is high in summer.
2.AB組分缺乏氣壓導致混合不均勻，凝膠化緩慢，顆粒簡單
2. The lack of air pressure of AB component leads to uneven mixing, slow gel and simple particles
3.B組件沒有進行過檢查和清洗B組分對水蒸氣敏感。由于運輸和儲存環境等偶然因素，B組件的表面可能會被剝皮，外殼的一部分被壓入管道中，很容易產生顆粒。
3. Component B has not been inspected and cleaned. Component B is sensitive to water vapor. Due to accidental factors such as transportation and storage environment, the surface of component B may be peeled, and part of the shell is pressed into the pipe, which is easy to generate particles.
4.過濾器和單向止回閥長時間未清洗。
4. The filter and one-way check valve have not been cleaned for a long time.
5.壓盤上的o形圈。B組件使用時間長，松動。
5. O-ring on pressure plate. Component B has been used for a long time and is loose.
丁基膠點膠機堵塞溶液:
Butyl glue dispenser blocking solution:
1.斷開膠水需要多長時間呢？建議每天涂膠前根據斷開時間前的溫度和濕度測量剝皮時間。另外，目前的客戶往往要求膠水的固化時間快，停止時間長，簡單造成顆粒的出現。
1. How long does it take to disconnect the glue? It is recommended to measure the peeling time according to the temperature and humidity of the day before the disconnection time before gluing every day. In addition, current customers often require that the curing time of glue is fast and the stopping time is long, which simply causes the appearance of particles.
2.簡單的解決辦法是用刮刀在不影響膠水使用的情況下清洗外殼。
2. The simple solution is to clean the shell with a scraper without affecting the use of glue.
3.建議定期清洗過濾器、單向止回閥、靜態混合器和膠槍。
3. It is recommended to clean the filter, one-way check valve, static mixer and glue gun regularly.
The reason for the blocking of butyl rubber beater is basically the content explained above. You can use it as a reference. For more related matters, please visit our website http://www.vrqf.com.cn Consult and understand.
上一篇：雙組份打膠機的結構原理簡單好理解
下一篇：雙組份打膠機操作時的詳細步驟
