雙組份打膠機的性能及介紹
氣動雙組份打膠機是集國內外技術生產的中空玻璃密封膠打膠機，A組分泵和B組分泵膠分別采用氣動系統驅動，采用無觸點電器控制系統控制，換向靈敏可靠，其獨特的方便可調試配比機構，大限度地保證雙組份膠近乎苛刻的配比要求，出膠連續均勻，涂膠效果好，生產效率高。
High efficiency pneumatic two-component glue machine is a set of insulating glass sealant production technology at home and abroad the best glue machine, A components and B components of pump pump respectively using pneumatic drive system, electric control system adopts contactless commutation control, sensitive and reliable, its unique convenient adjustable ratio mechanism. To ensure maximum two-component adhesive demanding ratio, glue uniform, good gluing effect, high production efficiency.
打膠操作：
Glue operation:
1）松開比例杠桿上的比例泵鎖緊螺釘，將比例泵內外調整所需比例。只有當A膠和B膠的配比達到正常值時，才可進行下面的操作。
1) unlock the proportion pump locking screw on the proportional lever, and adjust the ratio pump to the required proportion. Only when the ratio of A glue and B glue reaches the normal value, the following operation can be carried out.
2）置選擇旋鈕于A、B泵開，將膠槍出口對準兩片玻璃的中縫，打開膠槍開關，以適當速度平穩地移動膠槍使玻璃槽內的雙組份膠填滿充實為佳。打膠結束時關閉膠槍。
2) set the option knob on A and B pump, open the rubber gun outlet to the two piece of glass seam, open the glue gun switch, and move the glue gun smoothly at a suitable speed, so that the two component glue in the glass tank can be filled and enriched. Turn off the glue gun at the end of the glue.
因雙組份膠是由兩種膠混合而成的，其凝固速度與環境溫度和A、B膠的比例有關，混合后的膠一般在20分鐘之內就會反應固化。所以，當設備在正常打膠后，20分鐘之內不使用就必須將混合后的膠沖洗出來，以免堵塞混膠器和膠槍。具體操作：將B泵關閉，打開B膠回流開關然后打開膠槍，膠條為白色即可。
Because the two component adhesive is made of two kinds of glue, its solidification speed is related to the ambient temperature and the proportion of A and B glue. After mixing, the glue will react and solidify in 20 minutes. Therefore, when the equipment is not used in 20 minutes after normal glue, the mixed glue must be flushed out in order to avoid blocking the mixer and glue gun. Specific operation: close the B pump, open the B glue reflux switch and open the glue gun to the white glue bar.
感謝大家在百忙之中關注公司發布的產品信息，如果你想要了解更多，可以來我們公司咨詢。我們歡迎大家的光臨，并與你的合作！
Thank you for paying attention to the product information issued by the company in the busy schedule. If you want to know more, you can come to our company for consultation. We welcome everyone's presence and cooperate with you!
上一篇：雙液點膠機的應用及維護方法
下一篇：如何避免雙組份打膠機混合不均勻？
